651型止水帶

橡膠止水帶的品種規格比較多,按形狀可以分為:山型、橋型、P型、U型、Z型、乙型、T型、H型、E型、Q型等。如果按使用情況又可分類為背貼式和埋式橡膠止水帶，因為橡膠具有良好的彈性,耐磨性、耐老化性和抗撕裂性能,所以橡膠止水帶具有適應變形能力強、防水性能好的特點,按國產規定橡膠止水帶的溫度使用范圍為-45℃-+60℃，當溫度超過70℃,或受強烈的氧化作用或受油類等有機溶劑侵蝕時,均不得使用橡膠止水帶。

產品數據

橡膠止水帶產品應用范圍及標準

橡膠止水帶與遇水膨脹橡膠止水帶一樣都可以應用于地下構筑物、水壩、貯水池、游泳池、屋面以及其他建筑物質和構筑物的變形縫防水中使用。本產品主要用于混凝土現澆時設在施工縫及變形縫內，與混凝土結構成為一體的基礎工程、地下設施、隧道涵洞、輸水渡槽、擋水壩等，確保工程建設的使用壽命。

橡膠止水帶的生產完全采用國家GB 18173.2-2014《高分子防水材料 第2部分:止水帶》標準組織生產的?？砂从脩粢笊a(chǎn)各種止水帶形狀、尺寸的產品，另外還為不同工程、不同部位的需要備有十字型，丁字型、斜度型和內外轉角型橡膠止水帶接頭產品，可適用于任何設計要求。

橡膠止水帶的施工與安裝

在施工中，在混凝土澆注過程式中把橡膠止水帶部分或全部澆埋在混凝土中，如果混凝土中有許多尖角的石子和銳利的鋼筋頭，由于橡膠的撕裂強度比拉伸強低3-5倍，因此一旦被刺破或撕裂時，不需很大外外力裂口就會擴大，所以在止水帶定位和混凝土澆搗過程中，應注意定位方法和澆搗壓力,以免止水帶被刺破，所以在止水帶定位和混凝土澆搗過程中，應注意定位方法和澆搗壓力，以免被刺破，影響止水帶的防水效果,具體注意事項如下:

A、橡膠止水帶不能長時間露天曝曬，防止雨淋，勿與污染性強的化學物質接觸。產品應存放場所最好保持-10℃-+30℃，相對濕度在40%-80%。

B、在產品的運輸和施工中，防止機械，鋼筋損傷。成品存放和運輸中應取直平放，勿加重壓。

C、在施工過程中，產品安裝必須固定，避免在澆注混凝土時發生位移，保證止水帶在混凝土中的正確位置。

D、通常我們固定止水帶的方法有:利用附加鋼筋固定;專用卡具固定;鉛絲和模板固定等，如需穿孔時，只能選在止水帶的邊緣安裝區，不得損傷其它部分。

E、用戶定貨時應根據工程結構，設計圖紙計算好產品長度，異型結構要有圖紙說明，盡量在工廠中將止水帶連接成整體，如需在現場連接時，可采用電加熱板硫化粘合或冷粘接(橡膠止水帶)或焊接(塑料止水帶)的方法。

651型止水帶是止水帶的一種常用型號，屬于中埋式止水帶，中心孔兩側各有3個突起的楞，具體型式請見圖，而651型橡膠止水帶又是止水帶產品里使用廣泛的，常用的中埋式止水帶還有652型、653型等。The 651 type sealing strip is a common type of sealing strip, belonging to medium buried waterstop, the center hole of each of the 3 sides of the protruding arris, the specific type is shown in Figure 651, type rubber sealing belt is widely used in sealing products, commonly used in buried waterstop and type 652, 653 type.

651型止水帶安裝在施工中，在混凝土澆注過程式中把橡膠止水帶部分或全部澆埋在混凝土中，如果混凝土中有許多尖角的石子和銳利的鋼筋頭，由于橡膠的撕裂強度比拉伸強低3-5倍，因此一旦被刺破或撕裂時，不需很大外外力裂口就會擴大，所以在止水帶定位和混凝土澆搗過程中，應注意定位方法和澆搗壓力,以免止水帶被刺破，所以在止水帶定位和混凝土澆搗過程中，應注意定位方法和澆搗壓力，以免被刺破，影響止水帶的防水效果,具體注意事項如下: A、橡膠止水帶不能長時間露天曝曬，防止雨淋，勿與污染性強的化學物質接觸。The 651 type waterstop in construction, the rubber sealing strip of all or part of pouring buried in concrete in concrete pouring process, if there are many sharp stones and sharp head reinforced concrete, the tear strength of rubber and low tensile 3-5 times, so once punctured or torn, without a great force will expand, so the waterstop positioning and concrete pouring process, should pay attention to positioning method and pouring pressure, so as to avoid the water stop was punctured, so in the waterstop positioning and concrete pouring process, should pay attention to positioning method and pouring pressure, so as not to be punctured, affecting sealing waterproof effect with the specific considerations are as follows: A, rubber sealing can not long time outdoor exposure, to prevent rain, do not contact with the chemical substances with strong.

產品應存放場所最好保持-10℃－+30℃，相對濕度在40%－80%。 B、在產品的運輸和施工中，防止機械，鋼筋損傷。成品存放和運輸中應取直平放，勿加重壓。The product should be stored to keep the best places for -10 +30 C C, relative humidity in 40%80%. B, in the transportation and construction of the products, prevent mechanical and steel damage. In the storage and transportation of the finished product, it should be put in flat, without heavy pressure.C、在施工過程中，產品安裝必須固定，避免在澆注混凝土時發生位移，保證止水帶在混凝土中的正確位置。C, in the process of construction, the installation of the product must be fixed to avoid the displacement of concrete in the concrete and to ensure the correct position of the water stop in the concrete.D、通常我們固定止水帶的方法有：利用附加鋼筋固定；專用卡具固定；鉛絲和模板固定等，如需穿孔時，只能選在止水帶的邊緣安裝區，不得損傷其它部分。D, we usually fixed strip methods are: the use of additional reinforcement fixation; special fixture fixed; the wire and the fixed template, such as perforation, can only choose the installation area on the strip edge, not to damage other parts.E、用戶定貨時應根據工程結構，設計圖紙計算好產品長度，異型結構要有圖紙說明，盡量在工廠中將止水帶連接成整體，如需在現場連接時，可采用電加熱板硫化粘合或冷粘接(橡膠止水帶)或焊接(塑料止水帶)的方法，如用戶連接有困難，我公司可派技術人員現場指導。 止水帶分類止水帶系采用彈性材料，并摻加多種輔加助劑，經混煉、硫化而制成。

E, the user order should be based on the engineering structure design drawings, calculate the length of products, have special structure drawings and specifications, try to connect into a whole band in the factory will stop, if necessary in the field of connection, can use electric heating plate vulcanization bonding or cold bonding (rubber waterstop) or welding (plastic waterstop). Methods, such as the user is connected with the difficulties, our company can send technical personnel on-site guidance. The classified water stop belt of the water stop belt is made of elastic material and mixed with a variety of auxiliary additives, and is made by mixing and vulcanization.

根據產品選用材質的不同可分為天然橡膠止水帶 氯丁橡膠止水帶 丁腈橡膠止水帶 三元乙丙橡膠止水帶 塑料（PVC）止水帶 止水帶接頭。 根據結構形式的不同又可分為：CB型橡膠止水帶 CP型橡膠止水帶 EB型橡膠止水帶 EP型橡膠止水帶 根據使用安裝方式的不同可分為：中埋式止水帶、外貼式止水帶、可卸式止水帶。According to the material selection of products, it can be divided into natural rubber sealing belt, neoprene rubber sealing belt, nitrile rubber water stop belt three yuan, ethylene propylene rubber water stop plastic (PVC) water stop and water stop joint. According to the different form of structure, it can also be divided into: CB rubber water stop, CP rubber water stop, EB rubber water stop, EP type rubber water stop. According to the different installation methods, it can be divided into: buried water stop belt, external paste type water stop belt and discharge type water stop belt.

651型止水帶是止水帶的一種常用型號，屬于中埋式止水帶，中心孔兩側各有3個突起的楞，具體型式請見圖，而651型橡膠止水帶又是止水帶產品里使用廣泛的，常用的中埋式止水帶還有652型、653型等。The 651 type sealing strip is a common type of sealing strip, belonging to medium buried waterstop, the center hole of each of the 3 sides of the protruding arris, the specific type is shown in Figure 651, type rubber sealing belt is widely used in sealing products, commonly used in buried waterstop and type 652, 653 type.

651型止水帶安裝在施工中，在混凝土澆注過程式中把橡膠止水帶部分或全部澆埋在混凝土中，如果混凝土中有許多尖角的石子和銳利的鋼筋頭，由于橡膠的撕裂強度比拉伸強低3-5倍，因此一旦被刺破或撕裂時，不需很大外外力裂口就會擴大，所以在止水帶定位和混凝土澆搗過程中，應注意定位方法和澆搗壓力,以免止水帶被刺破，所以在止水帶定位和混凝土澆搗過程中，應注意定位方法和澆搗壓力，以免被刺破，影響止水帶的防水效果,具體注意事項如下: A、橡膠止水帶不能長時間露天曝曬，防止雨淋，勿與污染性強的化學物質接觸。The 651 type waterstop in construction, the rubber sealing strip of all or part of pouring buried in concrete in concrete pouring process, if there are many sharp stones and sharp head reinforced concrete, the tear strength of rubber and low tensile 3-5 times, so once punctured or torn, without a great force will expand, so the waterstop positioning and concrete pouring process, should pay attention to positioning method and pouring pressure, so as to avoid the water stop was punctured, so in the waterstop positioning and concrete pouring process, should pay attention to positioning method and pouring pressure, so as not to be punctured, affecting sealing waterproof effect with the specific considerations are as follows: A, rubber sealing can not long time outdoor exposure, to prevent rain, do not contact with the chemical substances with strong.

產品應存放場所最好保持-10℃－+30℃，相對濕度在40%－80%。 B、在產品的運輸和施工中，防止機械，鋼筋損傷。成品存放和運輸中應取直平放，勿加重壓。The product should be stored to keep the best places for -10 +30 C C, relative humidity in 40%80%. B, in the transportation and construction of the products, prevent mechanical and steel damage. In the storage and transportation of the finished product, it should be put in flat, without heavy pressure.C、在施工過程中，產品安裝必須固定，避免在澆注混凝土時發生位移，保證止水帶在混凝土中的正確位置。C, in the process of construction, the installation of the product must be fixed to avoid the displacement of concrete in the concrete and to ensure the correct position of the water stop in the concrete.D、通常我們固定止水帶的方法有：利用附加鋼筋固定；專用卡具固定；鉛絲和模板固定等，如需穿孔時，只能選在止水帶的邊緣安裝區，不得損傷其它部分。D, we usually fixed strip methods are: the use of additional reinforcement fixation; special fixture fixed; the wire and the fixed template, such as perforation, can only choose the installation area on the strip edge, not to damage other parts.E、用戶定貨時應根據工程結構，設計圖紙計算好產品長度，異型結構要有圖紙說明，盡量在工廠中將止水帶連接成整體，如需在現場連接時，可采用電加熱板硫化粘合或冷粘接(橡膠止水帶)或焊接(塑料止水帶)的方法，如用戶連接有困難，我公司可派技術人員現場指導。 止水帶分類止水帶系采用彈性材料，并摻加多種輔加助劑，經混煉、硫化而制成。

E, the user order should be based on the engineering structure design drawings, calculate the length of products, have special structure drawings and specifications, try to connect into a whole band in the factory will stop, if necessary in the field of connection, can use electric heating plate vulcanization bonding or cold bonding (rubber waterstop) or welding (plastic waterstop). Methods, such as the user is connected with the difficulties, our company can send technical personnel on-site guidance. The classified water stop belt of the water stop belt is made of elastic material and mixed with a variety of auxiliary additives, and is made by mixing and vulcanization.

weixin15030826464

根據產品選用材質的不同可分為天然橡膠止水帶 氯丁橡膠止水帶 丁腈橡膠止水帶 三元乙丙橡膠止水帶 塑料（PVC）止水帶 止水帶接頭。 根據結構形式的不同又可分為：CB型橡膠止水帶 CP型橡膠止水帶 EB型橡膠止水帶 EP型橡膠止水帶 根據使用安裝方式的不同可分為：中埋式止水帶、外貼式止水帶、可卸式止水帶。According to the material selection of products, it can be divided into natural rubber sealing belt, neoprene rubber sealing belt, nitrile rubber water stop belt three yuan, ethylene propylene rubber water stop plastic (PVC) water stop and water stop joint. According to the different form of structure, it can also be divided into: CB rubber water stop, CP rubber water stop, EB rubber water stop, EP type rubber water stop. According to the different installation methods, it can be divided into: buried water stop belt, external paste type water stop belt and discharge type water stop belt.